Setting up to resume a print after a power failure or planned power down
These instructions relate to RepRapFirmware 1.20. The auto-save facility was first introduced in version 1.19, however improvements in 1.20 necessitated changes to the configuration mechanism.
RepRapFirmware can be configured to allow you to resume a print after loss of power. This can be used in two ways:
- To handle unplanned power outages
- You can pause the print, turn off the heaters, wait for the hot end to cool, and turn the printer off (e.g. because you are no longer available to attend it).
- If you want to handle unplanned power outages, you should use 24V power, not 12V. If you use 12V power then it is most unlikely that there will be sufficient power left to lift the print head and save the resume information when power failure is detected.
- You must be able to re-home the printer (possibly using a different homing sequence from normal) with a print on the bed.
- If the print becomes detached from the bed while the power is off due to loss of bed heat, you won't be able to resume the print.
- The head must not drop down onto the print when power is removed.
How it works
- Any time you pause a print from SD card, the state of the print is saved to a special file on the SD card, sys/resurrect.g
- On the Duet 2, you can also also use the M911 command in config.g to enable automatic pause and state saving when low VIN voltage is detected
- You must set up file sys/resurrect-prologue.g to home the printer, taking account of the fact that there will be a print on the bed
- When the power supply voltage drops below the auto-pause threshold voltage, the heaters are turned off to conserve power, the state of the print is saved to file sys/resurrect.g on the SD card, the power fail script specified in the M911 command is run, and the print is left in a paused state
- After the power is restored, you can use command M916 to resume the print from where it stopped. This command runs file sys/resurrect.g which calls sys/resurrect-prologue.g at an appropriate point to home the printer
Use the M911 command. Example for a 24V Cartesian printer:
M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"
In this example, the power fail procedure is execute if VIN drops below 21.0V. It does the following:
- Set X and Y motors to zero current (M913 X0 Y0). This is to make the power last longer. Don't do this on a delta printer. Important: use M913, not M906. This is because M906 won't execute until all queued moves have been completed, whereas M913 will execute immediately.
- Set relative movement mode (G91)
- Set relative extrusion mode (M83)
- Simultaneously lift the head and retract filament (G1 Z3 E-5 F1000)
Setting up the sys/resurrect-prologue.g file
When you print file sys/resurrect.g it performs the following operations:
- Set bed and chamber heater temperatures
- Set all tools and heaters to their saved temperatures and other parameters, and set tools to active or standby as needed (without executing tool change macros)
- Call sys/resurrect-prologue.g
- Restore fan speeds, move the head to where it stopped printing, and resume the print
At the very least, your sys/resurrect-prologue.g file must do the following:
- Home the printer, without crashing the head into the print. On a delta, or on a Cartesian or CoreXY printer with a Z max homing switch, you can home all axes. On other types of printers you may have to skip homing Z and use a G92 command to tell the printer the current Z coordinate. If you choose not to home an axis, then even if the print head hasn't moved since power down, the motor positions will change by up to 4 full steps compared to their position at power down. Note: recent firmware versions write a G92 command containing the coordinates at the time of failure into resurrect.g, just before the call to resurrect-prologue.g. So you may get away without homing axes. But it is still best to home any axes that you can (typically X and Y on a cartesian or CoreXY printer).
- Execute M116 to wait for all heaters to reach operating temperature. You may do this either before or after homing axes.
- If your power fail procedure in the M911 command retracts filament and your printer has a single nozzle, you may wish to undo the retraction.
Example for a delta printer:
M116 ; wait for temperatures G28 ; home all towers M83 ; relative extrusion G1 E4 F3600 ; undo the retraction that was done in the M911 power fail script
Example for a Cartesian or CoreXY printer using recent firmware (G92 command included in resurrect.g):
M116 ; wait for temperatures G28 X Y ; home X and Y, hope that Z hasn't moved M83 ; relative extrusion G1 E4 F3600 ; undo the retraction that was done in the M911 power fail script