Same goes for “PanelDue-5i”, can someone please post the *exact* 3D-Model to make a nice housing. By *exact* I do not mean to have all componentnames and so on for reverse engineering, but a true volume-bounding-box of components and mounting holes for a nice housing. Best, Lucas
I think you just put “M558 P0” in your “config.g” and uncomment “M401 ; deploy Z probe” & “M402 ; retract probe” by putting a “;” in front of it in your “bed.g“. At least that is how manual probing for me works pretty good! Be sure to have your probing points arranged in clockwise order for the system.
Hi, thanks for the tip with the “brew” - since I am a newbie to it, I first had to install brew itself before getting the commands to work - bossa started after installing the 3 brews without any flaw on a mb-air running 10.12.6 . THANKS!
In what “width” can the current for the steppers be adjusted: in 100mA steps? E.g. for a stepper with 2.4A(RMS) driving it with ca. 85% it is possible to adjust 2040mA?
How big should the 5Vdc supply be: 500mA or better 1000mA. Is a linear transformer better or a switching supply? (Is it correct to connect with a thick cable the 0V/GND of the VAC/24Vdc and VAC/5Vdc supplys to each other, so that they have the “same” GND-Level?)
Hi,
does it work with microPlyer for all given step settings?
e.g. in config.g: 8 mirco-steps set, microPlyer enabled:
then when executing moves by the (adaptive) microPlyer automatically interpolated to up to 256micro-steps
?
Best regards
48V -> Just what I was waiting for :-)
Same goes for “PanelDue-5i”, can someone please post the *exact* 3D-Model to make a nice housing. By *exact* I do not mean to have all componentnames and so on for reverse engineering, but a true volume-bounding-box of components and mounting holes for a nice housing. Best, Lucas
Hi, would be great if someone can elaborate on the max Watt or A/V-combination, that e0 & e1 can deliver.
I would like to drive a led-stripe with one of the unused extruder-heaters and have to know what it can draw there without a problem. Would be great…
For M308:
Is it maybe reasonable to change for Bnnn the explanation to something similar like this:
Bnnn ß-value (if used without Cnnn). If used with Cnnn the reciprocal (1/B) of the calculated Steinhart-Hart thermistor model B coefficient
I think you just put “M558 P0” in your “config.g” and uncomment “M401 ; deploy Z probe” & “M402 ; retract probe” by putting a “;” in front of it in your “bed.g“. At least that is how manual probing for me works pretty good! Be sure to have your probing points arranged in clockwise order for the system.
Can somebody please elaborate on the connection of the variables to the definition within M302?
Would be great to have a linux tutorial - guess it would be similar to mac?
Hi, thanks for the tip with the “brew” - since I am a newbie to it, I first had to install brew itself before getting the commands to work - bossa started after installing the 3 brews without any flaw on a mb-air running 10.12.6 . THANKS!
In what “width” can the current for the steppers be adjusted: in 100mA steps? E.g. for a stepper with 2.4A(RMS) driving it with ca. 85% it is possible to adjust 2040mA?
Thanks in advance, Lucas
How big should the 5Vdc supply be: 500mA or better 1000mA. Is a linear transformer better or a switching supply? (Is it correct to connect with a thick cable the 0V/GND of the VAC/24Vdc and VAC/5Vdc supplys to each other, so that they have the “same” GND-Level?)
Page 1 of 2
Next