Skip to main content
/

Site Navigation

Your Account

Choose Language

Changes to Step #10

Edit by Ian A-S

Edit approved by Ian A-S

Before
After
Unchanged

Step Lines

[title] Duet 2 Ethernet and Duet 2 Maestro - Enable Ethernet Connection
[* black] '''DHCP.'''If you have setupPlug an ethernet cable into the Duet's ethernet port and connect the other end of the cable to a free ethernet port on your router/network hub.
[* icon_caution] The
Duet 2 Ethernet to use DHCP then when the networkand Duet 2 Maestro come with a factory-configured fixed IP address for testing. This is enabled it will lookunlikely to work for a DHCP serveryou setup!
[* black] So you need
to allocate an address.change the network settings. There are two options:
[* black] '''DHCP:'''
Most home routers are setup to assign IP addresses by DHCP.
[* black]
Send the command "M552 S1"'''M552 S0''' to the board.
[* black] After about 30 seconds, the board should reply with '''Network running'''
disable networking, then '''M552 S1 P0.0.0.0''' to enable networking and thehave your router assign an IP address that the Duet has been assigned.
[*
address.
[*
black] '''Fixed Address''' If you have used a fixed IP address in config.g then when the network is enabledAddress:''' You can set the Duet 2 Ethernet willto use thata fixed IP address. Note that if you use a fixed address, care should be taken that it does not conflict with other devices on the network.
[* icon_caution] The Duet 2 Ethernet and Duet 2 Maestro come with a factory configured fixed
Send '''M552 S0''' to disable networking, then '''M552 S1 Px.x.x.x''' to enable networking, where "x.x.x.x" is the IP address used during testing. This address will probably not workyou want to use, eg 192.168.1.15.
[* black] In both cases, after 10-30 seconds the board should reply
with your network'''Network running''' and may cause conflicts. Itthe IP address the Duet is recommendedusing. Send '''M552''' to enable DHCP when usingcheck the [https://configurator.reprapfirmware.org/|RepRapFirmware configurator]to generate your configuration filesettings.
[* icon_caution] Note: these network settings are temporary! They will be lost when you restart and will have to be re-entered. Step 10 and 11 explain how to set it up permanently
.
[* black] '''DHCP.'''If you have setupPlug an ethernet cable into the Duet's ethernet port and connect the other end of the cable to a free ethernet port on your router/network hub.
[* icon_caution] The
Duet 2 Ethernet to use DHCP then when the networkand Duet 2 Maestro come with a factory-configured fixed IP address for testing. This is enabled it will lookunlikely to work for a DHCP serveryou setup!
[* black] So you need
to allocate an address.change the network settings. There are two options:
[* black] '''DHCP:'''
Most home routers are setup to assign IP addresses by DHCP.
[* black]
Send the command "M552 S1"'''M552 S0''' to the board.
[* black] After about 30 seconds, the board should reply with '''Network running'''
disable networking, then '''M552 S1 P0.0.0.0''' to enable networking and thehave your router assign an IP address that the Duet has been assigned.
[*
address.
[*
black] '''Fixed Address''' If you have used a fixed IP address in config.g then when the network is enabledAddress:''' You can set the Duet 2 Ethernet willto use thata fixed IP address. Note that if you use a fixed address, care should be taken that it does not conflict with other devices on the network.
[* icon_caution] The Duet 2 Ethernet and Duet 2 Maestro come with a factory configured fixed
Send '''M552 S0''' to disable networking, then '''M552 S1 Px.x.x.x''' to enable networking, where "x.x.x.x" is the IP address used during testing. This address will probably not workyou want to use, eg 192.168.1.15.
[* black] In both cases, after 10-30 seconds the board should reply
with your network'''Network running''' and may cause conflicts. Itthe IP address the Duet is recommendedusing. Send '''M552''' to enable DHCP when usingcheck the [https://configurator.reprapfirmware.org/|RepRapFirmware configurator]to generate your configuration filesettings.
[* icon_caution] Note: these network settings are temporary! They will be lost when you restart and will have to be re-entered. Step 10 and 11 explain how to set it up permanently
.
[* icon_note] Mac users: Press CRTL-A and then CRTL-D to exit screen and return to terminal. You can safely close Terminal at this point.