Skip to main content

Site Navigation

Your Account

Choose Language

Changes to Ender 3 Pro and Duet Maestro Guide Part 4: Calibration Introduction

Edit by Jason Znack

Edit approved by Jason Znack

Deleted
Added
Unchanged
Introduction
In the previous guides in this series we went through installing a Duet 2 Maestro in a stock Ender 3 Pro, configured RepRapFirmware to work with it, and tested all of the hardware and electronics. [ … ] https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+1:+Wiring/37 https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+2:+Configuration/38 https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39 [ ] InIn this 4th and final guide in the Ender 3 series, we will go through initial calibration of the printer to determine crucial ensure reliable print parameters. quality. We will cover initial bed leveling, tuning the heaters, calibrating the extruder, and finding the optimal settings for the slicer. [ … ] Though this guide is specific to the Ender 3, the procedures shown here are the same for any printer during initial calibration. [ … ] '''Other guides in this series:''' * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+1:+Wiring/37?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+2:+Configuration/38?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40?lang=en
In the previous guides in this series we went through installing a Duet 2 Maestro in a stock Ender 3 Pro, configured RepRapFirmware to work with it, and tested all of the hardware and electronics. [ … ] https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+1:+Wiring/37 https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+2:+Configuration/38 https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39 [ ] InIn this 4th and final guide in the Ender 3 series, we will go through initial calibration of the printer to determine crucial ensure reliable print parameters. quality. We will cover initial bed leveling, tuning the heaters, calibrating the extruder, and finding the optimal settings for the slicer. [ … ] Though this guide is specific to the Ender 3, the procedures shown here are the same for any printer during initial calibration. [ … ] '''Other guides in this series:''' * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+1:+Wiring/37?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+2:+Configuration/38?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+3:+Commissioning/39?lang=en * https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40?lang=en

Steps

Step #: 1
Before
After
Step #: 2
Before
After
Step #: 3
Before
After
Step #: 4
Before
After
Step #: 5
Before
After
Step #: 6
Before
After
Step #: 7
Before
After